Call (410) 465-4636

Toyota

/Toyota

We Service and Repair All Toyota Cars and Trucks

2015 Toyota Camry

2019-11-13T23:00:18+00:00

Toyota Camry

Mileage
69,799
Service Date
10/23/2019
Services Performed
  • BG Seasonal Maintenance Special includes: Regular Oil and Filter change with fluids topped off. (Synthetic oil extra) Tire rotation and brake inspection. (Tire Balance extra) Inspection of the air filter and throttle plates. (Throttle plates are what regulate the amount of air that enters the engine.) Emission Health Check, test computer system for proper vehicle operation and pull computer codes as necessary. Perform 40 point inspection which includes all lighting, tires, front and rear suspension, all fluids, exhaust system, belts, hoses, fuel system and test the battery. Add BG's CF5 fuel system conditioner and carbon cleaner to fuel system. Please make sure you have a full tank of fuel for optimum cleaning. Add BG MOA oil additive for optimum engine lubrication. See below for results.
 
Ryan S. gave our service a 5 star review on 11/11/2019
2015 Toyota Camry 2019-11-13T23:00:18+00:00

2012 Toyota RAV4

2019-09-11T22:00:47+00:00

Toyota RAV4

Mileage
82,095
Service Date
9/4/2019
Services Performed
  • Mount and Balance new tires on vehicle.
 
Sean B. gave our service a 5 star review on 9/9/2019
2012 Toyota RAV4 2019-09-11T22:00:47+00:00

2015 Toyota Highlander

2019-09-01T22:01:11+00:00

Toyota Highlander

Mileage
51,079
Service Date
8/29/2019
Services Performed
  • Change Engine OIL and Filter. Lube Chassis where necessary. Inspect tires and adjust tire pressure as necessary. Inspect and top off all fluids. Minor inspection of car for needed services and maintenance.
  • Drain Master Cylinder and clean (where applicable) Fill Master Cylinder with new fluid. Open Bleeders, attach flushing equipment to pull new brake fluid through all 4 wheels until contaminated fluid is completely out of system.
  • Four Wheel Alignment: Road test vehicle for proper and improper road handling characteristics. Test for vehicle pull. (Vehicle pulling to either side can be one of two problems. The alignment out of specs can attribute to the pull as well as a tire itself causing the pull) Set up vehicle on alignment machine, Measure and set air pressure in tires to proper inflation. Take alignment readings. Inspect steering for any mechanical damage before making any adjustments. Evaluate readings and make all necessary adjustments. (Certain vehicles may require special adjustments above the normal toe and thrust angle adjustments which will incur extra time and associated costs) Road test vehicle for improved road handling. Note: Certain vehicles today have fixed alignment positions that are not adjustable. Some vehicles have no camber or caster adjustments. Pot holes can wreak havoc on certain steering and suspension systems. We make every attempt to bring your vehicle within specs. If the caster adjustments are out of specs and their is no adjustment then a pull to one side will be likely. The only way to repair is replacement of fixed suspension parts and possibly body shop repairs.
  • Mount and Balance new tires on vehicle
  • Remove front wheels. Remove front brake components. Remove existing pads from the brake calipers. Inspect brake caliper operation. Inspect brake hoses for durability and leaks. Reset brake calipers. Transfer over any necessary brake hardware to new brake pads and set new pads to the calipers. Remove brake rotors for machine work or replacement. Re-machine or replace front brake rotors as necessary. Measure finished brake rotor thickness to verify minimum thickness is within specs. Inspect and clean wheel hubs. Inspect and re-pack wheel bearings with grease as necessary. Re-install rotors on vehicle. Re-install brakes and wheels. Test brakes for proper operation. Machine work may be done with brake rotors on or off the vehicle. Road test for proper brake operation. Vehicle may also require a brake fluid flush. CAUTION: No panic stops for a day or so due to brake pads may need to seat. May need extra braking distance to stop during this period. This notice is generic and may not apply to you.
  • Remove rear wheels. Remove rear brake components. Remove existing pads from the brake calipers. Inspect brake caliper operation. Inspect brake hoses for durability and leaks. Reset brake calipers. Transfer over any necessary brake hardware to new brake pads and set new pads to the calipers. Remove brake rotors for machine work or replacement. Re-machine or replace rear brake rotors […]
2015 Toyota Highlander 2019-09-01T22:01:11+00:00

2007 Toyota Prius

2019-08-22T22:00:56+00:00

Toyota Prius

Mileage
108,069
Service Date
8/19/2019
Services Performed
  • Replace Seal at TPMS and balance tire.
 
Ollie H. gave our service a 5 star review on 8/21/2019
2007 Toyota Prius 2019-08-22T22:00:56+00:00

2012 Toyota Camry

2019-08-19T22:00:36+00:00

Toyota Camry

Mileage
110,705
Service Date
8/16/2019
Services Performed
  • Remove front wheels. Remove front brake components. Remove existing pads from the brake calipers. Inspect brake caliper operation. Inspect brake hoses for durability and leaks. Reset brake calipers. Transfer over any necessary brake hardware to new brake pads and set new pads to the calipers. Remove brake rotors for machine work or replacement. Re-machine or replace front brake rotors as necessary. Measure finished brake rotor thickness to verify minimum thickness is within specs. Inspect and clean wheel hubs. Inspect and re-pack wheel bearings with grease as necessary. Re-install rotors on vehicle. Re-install brakes and wheels. Test brakes for proper operation. Machine work may be done with brake rotors on or off the vehicle. Road test for proper brake operation. Vehicle may also require a brake fluid flush. CAUTION: No panic stops for a day or so due to brake pads may need to seat. May need extra braking distance to stop during this period. This notice is generic and may not apply to you.
  • WHEEL BEARING – Remove and Replace – Gas Front,One Side – [DOES NOT include wheel alignment.] – [Includes: Replace Inner and/or Outer Bearings, Cups, Seals and repack (where applicable).]
 
Jack/Brigette C. gave our service a 5 star review on 8/18/2019
2012 Toyota Camry 2019-08-19T22:00:36+00:00

2010 Toyota RAV4

2019-08-06T22:01:10+00:00

Toyota RAV4

Mileage
146,735
Service Date
8/1/2019
Services Performed
  • CVI Inspection: Perform Comprehensive Vehicle Inspection. See inspection sheet for results. Level: Test charging and battery system. Found alternator to have no output. Upper radiator hose is leaking.
  • ALTERNATOR ASSEMBLY – Remove, Install, and Overhaul – In-Line4 – [Includes: Replace components (as necessary).]
  • RADIATOR HOSE – Remove and Replace – Upper
  • Cooling System Service: Perform 3 step cooling system process using BG Coolant Flush System. Step 1 includes cooling system cleaner to loosen and remove scaling in the radiator, water pump and the engine. Step 2 includes the removal of the coolant and back flushing the coolant system. Step 3 includes adding conditioner and sealant with new coolant and protecting the coolant system from freezing to a minimum of -50 degrees. Re-inspect cooling system for leaks and proper operation. Road test as necessary for proper engine cooling operation. Note: The coolant system will sometimes get air trapped somewhere deep in the engine. They are called air pockets and may not all work themselves out at the time of service. While we attempt to keep air pockets to a minimum, sometimes it becomes necessary to top off the coolant when the air pockets work themselves out. We ask you to bring your vehicle back in a couple of days so we can perform a quick visual inspection of the coolant system and top off the coolant. This only takes a couple of minutes while you wait.
  • Perform BG Intake System Cleaning. This service is designed to loosen and remove carbon build up on the air intake system of the vehicle. Decarbonizing Top Engine Service. Remove all necessary engine components to access intake system. Connect decarbonizing unit to vehicle air intake system. Start engine, perform decarbonizing service. This process uses strong detergents to loosen carbon deposits that have built up over years of engine operation. Once the carbon has been softened, the next process helps remove the carbon sludge from the intake system. The process also cleans the intake valves in the engine and loosens and removes carbon inside the engine. (The final step requires the vehicle to be driven and the fuel additive continues to remove carbon. We recommend using an entire tank of gas before re-filling the gas tank as not to reduce the dilution of the cleaner.) Remove cleaning equipment and re-assemble any necessary engine components. Road test vehicle for proper engine performance. Carbon build up in the engine robs power and performance. Carbon absorbs the fuel that is intended to burn and causes the engine to not perform properly. (Run too lean) Carbon build up deep inside the engine also causes the internal engine temperature to exceed normal levels and causes excessive air pollutants. Thus causing the vehicle to fail emissions.
  • T-Tech Transmission Fluid Exchange: This fluid services the entire automatic transmission. Step 1, add transmission cleaner and run vehicle to circulate cleaner throughout transmission. Step 2, Connect transmission fluid exchanger to the vehicle's transmission lines. […]
2010 Toyota RAV4 2019-08-06T22:01:10+00:00

2007 Toyota Sienna

2019-07-31T22:01:04+00:00

Toyota Sienna

Mileage
139,658
Service Date
7/29/2019
Services Performed
  • Change Engine OIL and Filter. Lube Chassis where necessary. Inspect tires and adjust tire pressure as necessary. Inspect and top off all fluids. Minor inspection of car for needed services and maintenance.
  • SHOCK and /OR STRUT ASSEMBLY – Remove and Install or Remove and Replace – Both – [DOES NOT include disassemble or alignment.]
  • Four Wheel Alignment: Road test vehicle for proper and improper road handling characteristics. Test for vehicle pull. (Vehicle pulling to either side can be one of two problems. The alignment out of specs can attribute to the pull as well as a tire itself causing the pull) Set up vehicle on alignment machine, Measure and set air pressure in tires to proper inflation. Take alignment readings. Inspect steering for any mechanical damage before making any adjustments. Evaluate readings and make all necessary adjustments. (Certain vehicles may require special adjustments above the normal toe and thrust angle adjustments which will incur extra time and associated costs) Road test vehicle for improved road handling. Note: Certain vehicles today have fixed alignment positions that are not adjustable. Some vehicles have no camber or caster adjustments. Pot holes can wreak havoc on certain steering and suspension systems. We make every attempt to bring your vehicle within specs. If the caster adjustments are out of specs and their is no adjustment then a pull to one side will be likely. The only way to repair is replacement of fixed suspension parts and possibly body shop repairs.
  • Remove front wheels. Remove front brake components. Remove existing pads from the brake calipers. Inspect brake caliper operation. Inspect brake hoses for durability and leaks. Reset brake calipers. Transfer over any necessary brake hardware to new brake pads and set new pads to the calipers. Remove brake rotors for machine work or replacement. Re-machine or replace front brake rotors as necessary. Measure finished brake rotor thickness to verify minimum thickness is within specs. Inspect and clean wheel hubs. Inspect and re-pack wheel bearings with grease as necessary. Re-install rotors on vehicle. Re-install brakes and wheels. Test brakes for proper operation. Machine work may be done with brake rotors on or off the vehicle. Road test for proper brake operation. Vehicle may also require a brake fluid flush. CAUTION: No panic stops for a day or so due to brake pads may need to seat. May need extra braking distance to stop during this period. This notice is generic and may not apply to you.
 
Mike B. gave our service a 5 star review on 7/31/2019
2007 Toyota Sienna 2019-07-31T22:01:04+00:00

2015 Toyota 4Runner

2019-07-26T22:02:31+00:00

Toyota 4Runner

Mileage
107,887
Service Date
7/24/2019
Services Performed
  • Change Engine OIL and Filter. Lube Chassis where necessary. Inspect tires and adjust tire pressure as necessary. Inspect and top off all fluids. Minor inspection of car for needed services and maintenance.
  • Rotate tires, no balance.
  • SPARK PLUGS – Remove and Replace – All Applicable Models
  • Clean air filter
  • Remove rear wheels. Remove rear brake components. Remove existing pads from the brake calipers. Inspect brake caliper operation. Inspect brake hoses for durability and leaks. Reset brake calipers. Transfer over any necessary brake hardware to new brake pads and set new pads to the calipers. Remove brake rotors for machine work or replacement. Re-machine or replace rear brake rotors as necessary. Measure finished brake rotor thickness to verify minimum thickness is within specs. Inspect and clean wheel hubs. Inspect and re-pack wheel bearings with grease as necessary. Re-install rotors on vehicle. Re-install brakes and wheels. Test brakes for proper operation. Machine work may be done with brake rotors on or off the vehicle. Road test for proper brake operation. Vehicle may also require a brake fluid flush. CAUTION: No panic stops for a day or so due to brake pads may need to seat. May need extra braking distance to stop during this period. This notice is generic and may not apply to you.
 
John P. gave our service a 5 star review on 7/25/2019
2015 Toyota 4Runner 2019-07-26T22:02:31+00:00

2005 Toyota Prius

2019-07-25T22:01:14+00:00

Toyota Prius

Mileage
98,791
Service Date
7/23/2019
Services Performed
  • Computer System Diagnostic Service: Connect electronic test equipment to vehicles computer system. Test vehicles computer function's and pull Diagnostic Trouble Codes. Perform diagnostic and test procedures to determine fault. Diagnostic Trouble Codes present. Code: P3000, P0a80 Perform vehicle diagnostics tests to determine fault. Research technical library for Service Bulletins pertaining to this vehicle. Perform component testing and found the following failures: Found battery to be defective. Claim Number 897855 Total 3.5 hrs at $75 per hour. NOTE: Todays vehicle computers are becoming more complex and now require an extensive amount of mileage driven for the computer to reset and possibly turn the MIL or the CEL light back on. On some repairs, this may be experienced. This may be due to the route that was determined to take to fix the vehicle. This may also happen when their is a certain amount of codes in your vehicles computer and we repair the known problems first, then reset the computer system and the vehicle needs to be driven extensively to see if any computer codes are reset. This helps with not wasting time and money diagnosing and testing intermittent problems that are no longer present.
  • HIGH VOLTAGE BATTERY – Remove and Replace – Hybrid Battery Warranty Claim Number 897855
  • Computer System Diagnostic Service: Connect electronic test equipment to vehicles computer system. Test vehicles computer function's and pull Diagnostic Trouble Codes. Perform diagnostic and test procedures to determine fault. Diagnostic Trouble Codes present. Code: P0aa6 Perform vehicle diagnostics tests to determine fault. Research technical library for Service Bulletins pertaining to this vehicle. Perform component testing and found the following failures: Found battery to have failed. Claim Number 897859 Total 3.5 hrs at $75 per hour. NOTE: Todays vehicle computers are becoming more complex and now require an extensive amount of mileage driven for the computer to reset and possibly turn the MIL or the CEL light back on. On some repairs, this may be experienced. This may be due to the route that was determined to take to fix the vehicle. This may also happen when their is a certain amount of codes in your vehicles computer and we repair the known problems first, then reset the computer system and the vehicle needs to be driven extensively to see if any computer codes are reset. This helps with not wasting time and money diagnosing and testing intermittent problems that are no longer present.
  • HIGH VOLTAGE BATTERY – Remove and Replace – Hybrid Battery Warranty Claim Number 897859
 
Janet W. gave our service a 5 star review on 7/24/2019
2005 Toyota Prius 2019-07-25T22:01:14+00:00

2015 Toyota Sienna

2019-07-17T22:01:15+00:00

Toyota Sienna

Mileage
26,838
Service Date
7/12/2019
Services Performed
  • Mount and Balance new tires on vehicle from Tire Rack. 235/60/17 Goodyear Assurance Front Brakes have 12/33 Rear Brakes have 6/32 Noticed the LF Axle is Slinging is some Grease
  • Four Wheel Alignment: Road test vehicle for proper and improper road handling characteristics. Test for vehicle pull. (Vehicle pulling to either side can be one of two problems. The alignment out of specs can attribute to the pull as well as a tire itself causing the pull) Set up vehicle on alignment machine, Measure and set air pressure in tires to proper inflation. Take alignment readings. Inspect steering for any mechanical damage before making any adjustments. Evaluate readings and make all necessary adjustments. (Certain vehicles may require special adjustments above the normal toe and thrust angle adjustments which will incur extra time and associated costs) Road test vehicle for improved road handling. Note: Certain vehicles today have fixed alignment positions that are not adjustable. Some vehicles have no camber or caster adjustments. Pot holes can wreak havoc on certain steering and suspension systems. We make every attempt to bring your vehicle within specs. If the caster adjustments are out of specs and their is no adjustment then a pull to one side will be likely. The only way to repair is replacement of fixed suspension parts and possibly body shop repairs.
 
Ahima O. gave our service a 5 star review on 7/15/2019
2015 Toyota Sienna 2019-07-17T22:01:15+00:00